S36 Micro Diaphragm Small Liquid Pump

S36 Micro Diaphragm Small Liquid Pump

S36 is a high pressure liquid pump with adjustable flow rate. It is an electric diaphragm pump. It has two pump chambers and can output liquid with low pulsation.It is driven by a brushless motor and has two pump chambers, which can adjust the flow rate through control signals. It can dry run, can be self-priming, has good corrosion resistance, and can choose to configure different connectors according to application requirements. 

Overall Descriptions

S36 is a small liquid pump with linear adjustable liquid flow characteristics. It is driven by a brushless motor and has two pump chambers, which can adjust the flow rate through control signals. It can dry run, can be self-priming, has good corrosion resistance, and can choose to configure different connectors according to application requirements. Its liquid flow rate can reach up to 3L/min, and the maximum pressure is 1 Bar. If you are looking for a liquid pump with a lower flow rate, you can refer to S15 and S23 diaphragm liquid pump

 

Working Status Indicator

The knob speed control type and frequency speed control type are equipped with working status indicator lights, which can visually feed back the working status of the pump. The Top configuration type is equipped with an LCD touch screen that can display working status and fault codes.

Brush-less DC Motors

This model micro pump is driven by brushless motors which have the advantages of long service life, low interference and high reliability. It can run continuously for a long time, and the pumping life of the premium version can reach 10,000 hours.

Small Liquid Pump With Protections

Equipped with overheating protection, overload protection, power supply under-voltage and over-voltage protection and reverse connection protection function (except the basic type), which to the greatest extent prevents accidental damage to the pump.

Gas-liquid Dual Purpose

Liquid-gas dual-use, can be used as a liquid pump or a vacuum pump, can also be used to transfer gas-liquid mixed media; dry-run and self-priming

Modular Hydraulic Connector

This series of pumps has Rc1/8 internal thread interface, which can be installed with stainless steel push-in connectors (6mm and 8mm inner diameter), stainless steel hose connectors and PP hose connectors. This product is equipped with PP hose connectors as standard. The standard PP plastic hose connectors and the optional stainless steel hose connectors are recommended to match with 7*13 silicone hose. The size of the tube can be appropriately changed according to the softness and hardness of the hose.There are two options of stainless steel push-in connectors for matching with 6*8 or 4*6mm hard tubes. The user can select the corresponding hydraulic connectors when ordering according to the pipeline situation.

Speed Control Function

The flow rate of the pump can be changed by adjusting the motor speed. The Top configuration type is equipped with an LCD touch screen and speed control signal interface, which can be used to start and stop and control the motor speed through the LCD touch screen, and also through frequency signals. Knob speed control type models have an external speed control knob, which can control the speed, start and stop of the pump. Frequency speed control type models can be controlled by user inputting frequency signal.

Working Status Indication and Warning

1.The knob speed control type and frequency speed control type are equipped with working status indicator lights. Users can understand the working status of the equipment through the color change of the indicator lights:

  • When the green light is constantly on, it means that the power supply is normal and the pump is not working;
  • When the green light flashes, it means the pump is working normally;
  • When the red light flashes, it means the pump is working abnormally;
  • When the positive and negative poles are reversed, the indicator light is off, the pump does not work, but it will not damage the pump.

2.The touch control type and top configurationtype are equipped with an LCD touch screen. Alarm codes will be displayed when different faults occur, which makes fault handling more convenient. (The figure below is for illustration only, please refer to Chapter 5 Alarms and Troubleshooting for details.)

State Memory Function

When the micro pump is stopped due to abnormal power failure, the pump will continue to run according to the state and speed of the last power-off when the power supply is recovered. When using the knob or touch switch to start the pump, the pump will continue to run at the speed before the last shutdown. (Note: This function is only valid on the frequency speed control type, knob speed control type and top configuration type.)

Technical Infomation

S36 PERFORMANCE DATA

Model

S36S

Material Option

Diaphragm: EPDM

Valves: EPDM

Pump Head: Fiber reinforced PA6

Diaphragm: FKM

Valves: FKM

Pump Head: Fiber reinforced PA6

Voltage(V DC)

24

24

As Gas Pump

Max. Load Current (mA)

≤450

Max. Average Flow Rate (L/min)

≥1.0

Max. Vacuum (-kPa)

≥9

As Liquid Pump

Max. Load Current (mA)

≤500

Free Flow Rate (L/min)

≥1.3

Max. Suction Height (mWg)

1.7m

Flow Rate @ Max. Suction Height

0.8L/min

Max. Pressure Height (mWg)

7m

Flow Rate @ Max. Pressure Height

0.5L/min

Model

S36M

Material Option

Diaphragm: EPDM

Valves: EPDM

Pump Head: Fiber reinforced PA6

Diaphragm: FKM

Valves: FKM

Pump Head: Fiber reinforced PA6

Voltage(V DC)

24

24

As Gas Pump

Max. Load Current (mA)

≤500

Max. Average Flow Rate (L/min)

≥1.6

Max. Vacuum (-kPa)

≥15

As Liquid Pump

Max. Load Current (mA)

≤550

Free Flow Rate (L/min)

≥2.0

Max. Suction Height (mWg)

2m

Flow Rate @ Max. Suction Height

1.5L/min

Max. Pressure Height (mWg)

9m

Flow Rate @ Max. Pressure Height

0.8L/min

Model

S36L

Material Option

Diaphragm: EPDM

Valves: EPDM

Pump Head: Fiber reinforced PA6

Diaphragm: FKM

Valves: FKM

Pump Head: Fiber reinforced PA6

Voltage(V DC)

24

24

As Gas Pump

Max. Load Current (mA)

≤550

Max. Average Flow Rate (L/min)

≥2.2

Max. Vacuum (-kPa)

≥23

As Liquid Pump

Max. Load Current (mA)

≤650

Free Flow Rate (L/min)

≥3.0

Max. Suction Height (mWg)

3m

Flow Rate @ Max. Suction Height

2.0L/min

Max. Pressure Height (mWg)

11m

Flow Rate @ Max. Pressure Height

0.8L/min

S36 CONFIGRATION OPTIONS

Material Options


Pump Head

Fiber reinforced PA6

Diaphragm

EPDM

FKM

Valves

EPDM

FKM

Motor

BLDC

Connector Options

Default PA hose connector/ PP hose connector/ Stainless steel hose connector/ PC6 push-in quick connector/ PC8 push-in quick connector/ PA Rc1/8 inside thread

Function Options


Basic type

Knob speed control

Frequency speed control

Top configuration

S36 RELIABILITY DATA

Models

S36S/S36M/S36L

Versions

Simplified

Standard

Premium

Fully Loaded Lifetime(hrs)

2500

6000

10000

Unloaded Lifetime(hrs)

8000

12000

18000

Motor Lifetime(hrs)

10000

15000

20000

Test conditions

In a clean and non-corrosive laboratory, the pump is fully loaded (continuous pumping water) or unloaded (the inlet and outlet are directly connected to the atmosphere), and runs continuously around the clock; ambient temperature: 5℃~33 ℃, relative humidity: 50%-85%, fluctuates with the climate.

Working Condition

Operating temperature

Permissible ambient temperature is 0℃~50℃, it is not suitable to be exposed to the sun, and it should work in a clean and ventilated environment

Medium

Permissible temperature of the medium is 5℃~50℃ and gaseous media is 0℃~50℃, the transferring gas cannot contain solid particles or oil mist. It is not allowed to pump oily liquid and high viscosity liquid.

Wetted materials

EPDM, FKM as optional; fiber reinforced nylon,

tolerance to alcohol, acid, alkali, etc. (except strong acid, concentrated acid, lipids, benzene, gasoline, etc.)

Applications

  • Laboratory
  • Medical equipment
  • Analytical instruments
  • Printing

Downloads

S36 Diaphragm Small Liquid Pump – Hilintec Micro Pumps

S36 is a small liquid pump with linear adjustable liquid flow characteristics. It is driven by a brushless motor and has two pump chambers.

Product SKU: S36

Product Brand: Hilintec

Product Currency: USD

Price Valid Until: 2021-11-01

Product In-Stock: InStock

Editor's Rating:
4.77

Still got some more qurestions about this product?

We are very happy to get in touch with you and provide more information

Contact Us

Contact Us